Cook FCRU Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Küche Cook FCRU herunter. COOK FCRU User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 6
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
This publication contains the installation, operation and
maintenance instructions for standard units of the FCE /
FCRU Fiberglass Roof Exhausters.
FCED / FCEB
FCRUD / FCRUB
Carefully read this publication and any
supplemental documents prior to any
installation or maintenance procedure.
Loren Cook Fiberglass catalog provides additional
information describing the equipment, fan performance,
available accessories, and specification data.
For additional safety information, refer to AMCA
publication 410-96, Safety Practices for Users and Installers
of Industrial and Commercial Fans.
The publication(s) listed above can be obtained from
Loren Cook Company by phoning (417)869-6474,
extension 166; by FAX at (417)832-9431; or by e-mail at
For information and instructions on special equipment,
contact Loren Cook Company at 417.869-6474.
Receiving and Inspection
Immediately upon receipt of the fan, carefully inspect the
fan and accessories for damage and shortage.
• Turn the wheel by hand to ensure it turns freely and
does not bind.
• Check dampers (if included) for free operation of all
moving parts.
• Record on the Delivery Receipt any visible sign of
damage.
Rotating Parts & Electrical Shock Hazard:
Disconnect electric power before working on unit.
Follow proper lockout / tagout procedures to ensure
the unit cannot be energized while being installed or
serviced.
A disconnect switch should be placed near the fan in
order that the power can be swiftly cut off, in case of
an emergency and in order that maintenance
personnel are provided complete control of the power
source.
Grounding is required. All field-installed wiring must
be completed by qualified personnel. All field-
installed wiring must comply with National Electric
Code (NFPA 70) and all applicable local codes.
Failure to follow these instructions could result in
death or serious injury.
Fiberglass Roof Exhausters
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
Handling
Lift the fan by the shipping carton. NOTICE! Never lift by
the shaft, motor or housing.
Storage
If the fan is stored for any length of time prior to
installation, completely fill the bearings with grease or
moisture-inhibiting oil (refer to Lubricants on page 6).
Rotate the wheel several revolutions every three to five
days to keep a coating of grease on all internal bearing
parts.
Store the fan in its original crate and protect it from dust,
debris and the weather.
To maintain good working condition of the fan when it is
stored outdoors, follow the additional instructions below.
• Coat the shaft with grease or a rust preventative
compound.
• Wrap bearings for weather protection. Cover the inlet
and outlet to prevent the accumulation of dirt and
moisture in the housing.
• Periodically rotate the wheel and operate dampers (if
supplied). Periodically inspect the unit to prevent
damaging conditions.
Installation
If the fan was delivered with the motor unmounted, see
the maintenance section for belt and pulley installation.
FCE / FCRU
FCE
FCRU
Seitenansicht 0
1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - FCE / FCRU

This publication contains the installation, operation andmaintenance instructions for standard units of the FCE /FCRU Fiberglass Roof Exhausters.• FCE

Seite 2 - Final Installation Steps

2Damper InstallationIf your fan is supplied with dampers, follow the directionsbelow. If your fan does not include dampers, proceed to Belt and Pulley

Seite 3 - Operation

3Wiring DiagramsT-1T-4Ground BL2L1Ground ALineWiring DiagramsWhen ground is required, attach to ground A or B with no. 6 thread forming screw. To reve

Seite 4 - Maintenance

4InspectionInspection of the fan should be conducted at the first 30 minute, 8 hour and 24 hour intervals of satisfactory operation. During the inspec

Seite 5 - Pulley Alignment

5Replacing Pulleys and Belts1. Clean the motor and fan shafts.2. Loosen the motor plate mounting bolts to relieve the belt tension. Remove the belt. 3

Seite 6 - LOREN COOK COMPANY

6This warranty gives only the original purchaser placing the fan in service specifically the right. You may have other legal rights which vary from st

Verwandte Modelle: FCE

Kommentare zu diesen Handbüchern

Keine Kommentare